Skip to content
white prismatic reflective tape roll for outdoor visibility marking
White prismatic reflective tape reflecting light in the dark
Roll of white prismatic reflective tape partly unrolled
White prismatic tape widths available, 25 mm to 200 mm, shown at true relative width
Narrow roll of white prismatic reflective tape
Narrow roll of white prismatic reflective tape, side view
Wide roll of white prismatic reflective tape standing upright
Tall wide roll of white prismatic reflective tape
Extra wide roll of white prismatic reflective tape
White prismatic reflective tape technical data: construction and specification
White prismatic tape retroreflection test results measured by SATRA to CIE 54.2
white prismatic reflective tape roll for outdoor visibility marking
White prismatic reflective tape reflecting light in the dark
Roll of white prismatic reflective tape partly unrolled
White prismatic tape widths available, 25 mm to 200 mm, shown at true relative width
Narrow roll of white prismatic reflective tape
Narrow roll of white prismatic reflective tape, side view
Wide roll of white prismatic reflective tape standing upright
Tall wide roll of white prismatic reflective tape
Extra wide roll of white prismatic reflective tape
White prismatic reflective tape technical data: construction and specification
White prismatic tape retroreflection test results measured by SATRA to CIE 54.2

White Prismatic Reflective Tape | Flashback® Tape

Product Code: FB-PZ-WHT
£1.46 - £277.12
£1.46 Inc VAT
£1.22 - £230.93 Ex VAT
£1.46 - £277.12
£1.46 Inc VAT
£1.46/m Inc VAT £1.22/m Ex VAT
Choose a Width
Choose a Length (metres)

UK delivery £3.49 per order, however many rolls you add. Next day £4.95

Marking an HGV or trailer? Use approved ECE104 tape. Not sure which tape you need? Choose your reflective tape.

Buying in bulk or need a custom width? Request a trade quote

  • Retroreflective490 to 540 cd/(lx·m²) tested
  • Independently measuredSATRA, CIE 54.2
  • UV resistant
  • Flat, rigid surfaces
  • Apply above 10°C
  • Cut to length

Product Description

Flashback® White Prismatic Reflective Tape is clean white by day and bright at night. Its acrylic microprismatic surface sends headlight and torch light straight back towards the source, so posts, gates, edges and equipment stand out clearly in the dark.

A new sample measured 490 to 540 cd/(lx·m²) in independent SATRA tests, making it one of our brightest prismatic tapes, with a neutral finish that suits almost any surface. It is a self-adhesive tape for indoor and outdoor visibility marking where no particular certification or approved material is specified. It is not ECE104 compliant, so for certified conspicuity marking on HGVs over 7.5 tonnes or trailers over 3.5 tonnes, use our ECE104 Reflective Tape instead.

Download the Technical Data Sheet (PDF)

Why Acrylic Prismatic?

Prismatic reflective tapes use a face film of acrylic, PVC or PET. Ours is acrylic, the film generally chosen for long-term outdoor use because it resists UV and weathering and holds its colour and clarity. PVC and PET films are often cheaper, and PVC is more flexible, but both are generally less resistant to prolonged sunlight.

The trade-off is stiffness. Acrylic performs best on flat, rigid surfaces. For curves, corners and edges, our more flexible silver glass bead reflective tape is the better choice.

Key Features

  • 490 to 540 cd/(lx·m²) at 0.2°/−4° on a new sample, measured by SATRA to CIE 54.2
  • Clean white finish that suits almost any surface
  • Acrylic prismatic face, chosen for UV and weather resistance
  • Self-adhesive, for clean, smooth and rigid surfaces
  • Widths from 25mm to 200mm, cut to length from 1 to 45 metres

Related Guides

Uses & suitable surfaces

White gives a clean, neutral finish and returns plenty of light, which makes it a versatile choice for marking edges, posts and fixed objects. Popular uses include:

  • Gates, posts, letterboxes and bins
  • Private driveways and entrances
  • Warehouse and workshop identification
  • Plant, machinery and site equipment where no certified marking is specified
  • Fixed objects on private property, indoors and outdoors

Suitable surfaces may include clean, dry and smooth metal, painted metal, rigid plastic, glass, sealed wood and other stable, non-porous surfaces.

Adhesion depends on the surface condition, preparation, texture and application temperature. Test a small area before full installation.

For bollards and barriers, use only as supplementary visibility marking on privately owned items where no formal specification applies. It should not replace prescribed reflectors, approved traffic-management products or required safety components.

Product specifications

Product: Flashback® White Prismatic Reflective Tape

Product code: FB-PZ-WHT

Colour: White

Material: Acrylic prismatic reflective material

Backing: Self-adhesive

Retroreflection (0.2° / −4°): 490.0 to 540.3 cd/(lx·m²) when new, measured by SATRA Technology Centre to CIE 54.2, report no. SPC2048844/67550/1

Widths: 25mm, 50mm, 100mm, 150mm, 200mm

Lengths: 1–45 metres

Application temperature: Above 10°C

Application: Indoor and outdoor visibility marking where no certified material is specified

Surface type: Suitable clean, dry, smooth and rigid surfaces

Data sheet: FB-DS-PZ-WHT (PDF)

Test data

The coefficient of retroreflection (RA) shows how much light the tape returns towards its source. The higher the figure, the brighter the tape looks to someone near the light, such as a driver behind their headlights.

Values are in cd/(lx·m²), measured in two orientations: x (along the length of the tape) and y (across it).

Observation angle Entrance angle x orientation y orientation
0.2°−4°540.3490.0
0.2°+30°232.7161.7
0.33°+5°347.2278.9
0.5°−4°336.3307.1

RA values measured by SATRA Technology Centre to CIE 54.2 on a production sample, report no. SPC2048844/67550/1. Measurement uncertainty ±8%. These are typical values for new material from the sample tested, not a specification or guaranteed minimum. Dirt, abrasion and weathering reduce reflectivity over time. Prismatic material is orientation sensitive, so performance at wide angles can vary with the direction the tape is applied. No performance class or standard is claimed.

How to apply
  1. Check that the surface is suitable and test a small area.
  2. Remove dust, dirt, oil, wax and loose material.
  3. Allow the surface to dry completely.
  4. Apply when the surface and air are above 10°C.
  5. Measure and cut the required amount of tape using sharp scissors or a suitable knife.
  6. Peel back a small section of the release liner.
  7. Position the tape and apply it gradually using firm, even pressure.
  8. Check that the edges are firmly attached before exposing the tape to handling or outdoor conditions.

Adhesion depends on the surface, preparation, texture and application conditions. Do not apply over rust, loose paint, oil, moisture or heavily textured surfaces.

Certification & product guidance

This product is intended for visibility marking where no specific approval or certification is required.

It is not supplied as ECE104/R104-approved vehicle conspicuity material, certified traffic-sign sheeting or reflective PPE. The retroreflection values shown are informative measurements on a production sample, and no performance class or standard is claimed.

For regulated HGV and trailer conspicuity marking, view our ECE104-compliant vehicle tape.

Public-highway, roadworks, traffic-management and prescribed sign applications may require particular materials, colours, layouts or approvals. Check the applicable requirements before ordering for a regulated application.

Frequently asked questions

How reflective is this tape?
Its coefficient of retroreflection was measured by SATRA Technology Centre to CIE 54.2. At the standard 0.2° observation and −4° entrance angle it measured 490.0 to 540.3 cd/(lx·m²) when new, depending on orientation. Full results are in the Test data section and the technical data sheet.

Should I choose white or hi-vis yellow?
Both measured 490 cd/(lx·m²) or more at the standard angle, so head-on at night there is little between them. White held up better at wider observation angles in our tests, while hi-vis yellow is far more noticeable in daylight. Choose white for a clean, neutral look, or hi-vis yellow if daytime visibility matters most.

Does the direction I apply it matter?
At most viewing angles the difference is small, but prismatic tape is orientation sensitive. At wide angles, such as light hitting the tape from well off to the side, the result can be noticeably higher in one direction than the other.

Is this reflective tape suitable for outdoor use?
Yes. It is intended for indoor and outdoor visibility marking. Performance and service life vary according to the surface, preparation, installation, handling and exposure conditions.

What is the difference between acrylic and PVC prismatic reflective tape?
Acrylic prismatic film is generally chosen for long-term outdoor use because it resists UV, weathering and yellowing well, but it is stiffer and best suited to flat, rigid surfaces. PVC prismatic film is more flexible and conforms to curves more easily, but generally ages faster in prolonged sunlight. This tape uses acrylic. For curved surfaces, consider our more flexible silver glass bead reflective tape.

Can I use it on bollards or barriers?
It may be suitable for supplementary visibility on clean, smooth, privately owned bollards or barriers where no formal standard applies. Do not assume it meets requirements for public-highway, roadworks, traffic-management or safety-critical equipment.

Is this tape ECE104 compliant?
No. Where regulated HGV or trailer conspicuity markings are required, select approved ECE104/R104 reflective tape.

Can it be used on clothing or fabric?
No. This self-adhesive tape is intended for suitable rigid surfaces and is not reflective PPE material.

Can the tape be cut to size?
Yes. It can be cut using sharp scissors or a suitable knife. Take care when using cutting tools.

Can the tape be removed?
Yes, although adhesive residue may remain and some surfaces or coatings could be affected. Gentle heat may help soften the adhesive, but always test first.

Trade & Bulk Orders

Tell us the widths and lengths or number of full rolls you need, and we’ll reply with a quote. Trade orders can be paid by pro forma invoice.